GATE TITAN II Bluetooth Hpa

Five trigger sensors give you the option to adjust the sensitivity of the trigger. You do not have to open the gearbox for this. Via the GATE Control Station app, you can adjust the sensitivity!

Using two selector sensors you can select up to 6 different firing modes, such as the innovative SEMI-BURST-AUTO Mode!

-SAFE-SEMI-CAR

-SAFE-SEMI-SEMI

-SAFE-SEMI-BURST

-SAFE-BINARY-AUTO

(Advance firmware only)

All variations of SAFE/SEMI/BINARY/BURST/BURST-AUTO/AUTO

A total of 216 different modes

(Expert firmware only)

All variations of SAFE/SEMI/BINARY/BURST/BURST-AUTO/AUTO/SEMI-RAMPING

A total of 343 different modes

Thanks to the gear sensor, the TITAN can see exactly when the cycle is complete. This results in a complete firing cycle even with the shortest trigger action. This ensures, among other things:

-Automatic Burst: No more timing settings required. You can set between 2 and 10 shots burst.

-Automatic Pre-cocking: Pre-cocking boost no longer needs to be set manually, and now works in all firing modes (SEMI-BURST-AUTO). You only have to set High, Mid or Low.

-Full Cycle: As long as Pre-cocking is off, the gearbox always makes a complete cycle. This gives you higher reliability and consistency.

Winning or losing often takes a fraction of a second. Thanks to Pre-Cocking you can get a trigger response that closely resembles a real weapon. It ensures that the spring is already pre-tensioned, making the trigger response incredibly fast!

There are two Pre-Cocking modes:

1 Auto Mode: The spring is automatically tensioned after each shot (adjustable in levels 0 to 5)

2 Manual Mode: You can set it yourself, pay attention! This requires some technical knowledge to get the timing right.

*Pre-cocking is now also active in all fire modes (SEMI/BURST/AUTO) and pre-cocking settings are no longer necessary. NB! Pre-cocking ensures more wear and tear on the gearbox!

The burst function allows you to fire a preset number of BBs, which is very useful in MILSIMs and/or when using low/midcaps.

*Burst time no longer needs to be set. You only have to set the burst number.

Can be set as 3rnd or 5rnd burst

(Advance firmware only)

Can be set as 2rnd, 3rnd, 4rnd, 5rnd 8rnd & 10rnd burst

(Expert firmware only)

Can be set as 2 to 99rnd burst

The rate of fire can be reduced. You can now use stronger LiPos and still have a realistic rate of fire.

(Basic)

-OFF/100%/90%/80%/70%/60%/50% power

(Advanced)

-OFF/100%/90%/80%/70%/60%/50% power

-Delay

-Delay + power

(Expert)

-OFF/100-1% power

-Delay

-Delay + power

-Adaptive 1-100RPS

It lets you to set delay between each SEMI shots to simulate the delay from reload or recoil. You can set 0.5s, 1s, 2s or 3s delay.

(Expert)

Delay can be set from 0,01 to 5 seconds

Fast trigger response is vital during a fight. The Smart Trigger function has been developed for this purpose. It provides a faster trigger response in combination with the ROF Control System. During the first shot, the microprocessor sets the ROF Control to 100%. After the first shot, it switches to the preset ROF setting (e.g. 50%). This will cause the first shot to be fired at the full ROF, and the remainder at the reduced ROF. You will achieve the best results with a higher-than-standard voltage, such as an 11.1v LiPo.

*Only works if ROF is enabled.

AUG Mode enables a Two-Stage Trigger. Turn on the AUG Mode, and set two trigger sensitivities. By pressing the trigger to the first sensitivity you can shoot SEMI or BURST, and pulling further gives BURST or AUTO. (Depending on fire selector mode)

The Magazine function simulates your high cap conversion to a real/low capacity magazine. When you have shot the simulated low cap empty, you have to wait an x number of seconds. This provides extra realism during a skirm.

(Basic)

-OFF/30 BBs

(Advanced)

-OFF/30/45/115/145/185 BBs

(Expert)

-OFF/1-250 BBs

(Only Advanced & Expert firmware)

Low ammo warning

Protection against Over-Discharge of the Battery. Modern LiPo and LiFe batteries are very sensitive to over-discharge. If you do not want to damage the battery and you care about its service life, this protection is indispensable. The microprocessor monitors the battery voltage constantly. When the voltage drops down to a critical level, it will not allow firing.

*TITAN detects the number of cells automatically. There is no need to reprogram TITAN every time you replace the battery.

When the battery voltage drops to a predefined level, the motor will vibrate at regular intervals.  

We have developed an electronic fuse with an accurate current sensor. A combination of current, voltage and temperature measurements makes your AEG installation highly reliable. It protects the MOSFET against overheating, overloading and short-circuiting. If your airsoft gun becomes jammed, the function protects the motor and battery against damage.

It automatically adjusts the motor's braking power according to your needs. This prolongs the lifespan of the motor.

Do you want to achieve a higher ROF and faster trigger response? Are you planning a power upgrade of your gun? In that case, you need a MOSFET.

It targets the energy from the battery directly to the motor, bypassing the mechanical trigger contacts. As a result, you gain a higher ROF of the gun and a faster trigger response.

This allows you to quickly check whether the drop-in module is working properly. It helps to locate where the problem lies when anything goes wrong.

Thanks to its special conformal coating, our product is resistant to atmospheric conditions (Military Specification MIL-V-173C).

The product has factory-fitted low-resistance deans-t connectors.

The drop-in module can be used with batteries up to and including 14.8V LI-PO. The minimum operating voltage is 3V and maximum is 17V.